How to run Open PS2 Loader on your PS2 TOOL:
It is better to use this command as this is why somebody uses TOOL:
Code:
make DTL_T10000=1 NOT_PACKED=1 DEBUG=1 INGAME_DEBUG=1 DECI2_DEBUG=1
How to run Open PS2 Loader on your PS2 TOOL:
make DTL_T10000=1 NOT_PACKED=1 DEBUG=1 INGAME_DEBUG=1 DECI2_DEBUG=1
INGAME_DEBUG and DECI2_DEBUG are only necessary for debugging on retail models. For DTL-T debug output is already output due to the DECI2 libraries being embedded in the default ROM.It is better to use this command as this is why somebody uses TOOL:
This also will output more information in terminals.Code:make DTL_T10000=1 NOT_PACKED=1 DEBUG=1 INGAME_DEBUG=1 DECI2_DEBUG=1
I havnt seen any show up on ebay for years but they do pop up on yahoo auctions from time to time, tho with RonaTime you might not find any there for a while. Just a note, they don't really survive shipping, super fragileWhere do people find these kits? Saving eBay searches? I know they're relatively rare, with most people using the typical story of blaming it on Square Enix, but I've only been able to find TEST machines.
Ah, ouch.... I saw that photo of a TOOL destroyed in shipping, that really hurt. What are good alternatives for actual development? Using an emulator, or an RDB card on a retail unit?I havnt seen any show up on ebay for years but they do pop up on yahoo auctions from time to time, tho with RonaTime you might not find any there for a while. Just a note, they don't really survive shipping, super fragile
I probably wouldn't bother with home-brew on the actual hardware, pcsx2 compatibility is extremely high and the debugger is probably leaps and bounds betterAh, ouch.... I saw that photo of a TOOL destroyed in shipping, that really hurt. What are good alternatives for actual development? Using an emulator, or an RDB card on a retail unit?
Did you have any luck with that SBC? Or tool is only working with two options of SBC it came with?My IPC-PP827 board arrived. It seems the network ports and keyboard will power, but there is no display output or POST beep. Maybe I need to connect something to the power connector?
IPC-PP827 seems to be a rebranded version of PCI-827LF from Protech. In fact, it appears that all of the products on Ant Computer are rebranded Protech products.
Protech has a habit of removing manuals for older products, so I probably can't find the manual for the PCI-827LF (only the datasheet). However, the product catalog specifies the same P8/P9 to 10-Pin power (27-012-02501071) for multiple products, which contain the pinouts for the power connector:
https://www.protech.com.tw/Driver/BH-1105/BH-1105_M2.PDF (section 2-18)
https://www.protech.com.tw/Driver/PCI-531LF/PCI-531LF_M5.PDF (section 2-26)
Maybe I can stick two pins of the four pin power into pins 4 and 5 of the connector?
The manual of the PCI-586HVE-S seems to follow the same layout of the aforementioned manuals. Maybe Protech manufactured the PCI-586HVE-S too?
Also, my USB bracket arrived. The connector didn't fit since it was too small. However, I have the pinouts, so I can make my own cable later.
I was going to install a gigabit ethernet card, but I got a wrong PCI card (a SPIDF in/out card instead of a dual gigabit ethernet card), so the seller is sending me the right one.
I haven't tried it yet due to myself deferring the building of the serial and power cables.Did you have any luck with that SBC? Or tool is only working with two options of SBC it came with?
YesAlso planning to upgrade mine with celeron board, do you still have RHL6.2 images on hand?
I can confirm mine works with Sandisk Extreme 32gb.hello, i got my tool from Australia for really cheap because the hdds had died. what is the best cf card to use for this system? i have a lexar professional 32gb 1066x cf card from 2015 and when i use it with the HDD image copied to it, the system dosent post on boot. when i use a 256mb lexar media 8x cf card from 2002, the system posts and runs fine. what is the best cf card to use for this system.
i managed to play with the system today and im trying to run a disc from the disc drive, but when i run the commands i get a this is not a ps2 disc error. and i have tried multiple discs. any ideas. thanks