ok, if the xenon os dosent see the xex. then does that mean remote recoveries wont work. im asking for both me and a friend because he has had all except 1434 fail on him.
It's been maybe a month since I played the retail version of Full Auto, but looking at that video it seems like some parts of it actually look better than the final version. Like, the particle effects and car models look a bit better in the G5 version. The framerate is a lot worse in the G5 version, though.
slycooper124 said:
look at the bright side at least we can play games on this g5 more than just xbox original games
I think it's pretty cool, although unfortunately it's not possible to run this stuff on my G5 (it's a late-2005 dual-core model). Full Auto is interesting because it was probably one of the first games to begin development for the 360, and this proves that it was in development before the hardware was even finalized. I find the early 360 games really interesting for some reason, it's hard to say why. Maybe it's partly because they're more similar to the previous generation's games, which is a generation that I really love.
my network card just came today and i just tried to use the remote recovery and ISO recovery of 1434 and i cant get it to work. when i use the remote recovery, i get a little bit in and it gives me a white screen. on the ISO recovery i get stuck at the part where it says launching elf. and it hangs there vs flashing the screen like normal
ive installed 1529 iso on a hard drive it booted and installed fine. i rebooted the machine it came back to the dashboard for a few minutes and freezes. now when i turn on the g5 it goes straight to a blue loading bar?
Originally when i encountered cpu0 was only showing and getting the loading elf screen. i re seated and swapped cpus and xenon started to boot fine and then would freeze on anything i clicked to a blue loading bar. this issue was intermittent before i swapped the cpus. afrer i swaooed xenon os was running perfect many times everything worked. it rebooted itself and i keep getting that damn blue loading bar now.
so i try putting in another hard drive and install 1529. it loads installer no problems. but after the install it goes to white screen then black screen with blue loading bar? does ANYONE? know what is happening here? i could post screenshots, maybe someone else encountered this. its a whole nightmare getting this to work its been a complete problem from the start between the sellers and the cpu issue having to swap them and flashing the correct rom with absolute no artifacting. only when the monitor is set too high of resolution so i limited it in open firmare for 4:3 crt for dev. i do not even care to use the xbox emulator i want to develope some homebrew
y0rper said:
ive installed 1529 iso on a hard drive it booted and installed fine. i rebooted the machine it came back to the dashboard for a few minutes and freezes. now when i turn on the g5 it goes straight to a blue loading bar?
Originally when i encountered cpu0 was only showing and getting the loading elf screen. i re seated and swapped cpus and xenon started to boot fine and then would freeze on anything i clicked to a blue loading bar. this issue was intermittent before i swapped the cpus. afrer i swaooed xenon os was running perfect many times everything worked. it rebooted itself and i keep getting that damn blue loading bar now.
so i try putting in another hard drive and install 1529. it loads installer no problems. but after the install it goes to white screen then black screen with blue loading bar? does ANYONE? know what is happening here? i could post screenshots, maybe someone else encountered this. its a whole nightmare getting this to work its been a complete problem from the start between the sellers and the cpu issue having to swap them and flashing the correct rom with absolute no artifacting. only when the monitor is set too high of resolution so i limited it in open firmare for 4:3 crt for dev. i do not even care to use the xbox emulator i want to develope some homebrew
Reset your pram and nvram. Boot holding Cmd-opt-p-r. Go manually into open firmware and type reset-nvram. Make sure the hdd is in the A bank and is 160gb. Make sure you’re using non ecc 3200 ddr ram (512mb), 2 sticks of 256. Make sure network card is in top slot. Also make sure your pram battery is good or put a new one in. The problem you’re having with the blue loading bar (crash dump) kept happening to me until I reset nvram.
Thank you I am sure I have tried all of the above pram is nv ram? So we cleared it? I’ll try your way. Also we had used a different hdd and it seemed to work as quoted above. Thanks for the input I
do not have a network card yet. I’ll post photos on my lunch break just ffs and in meantime has anyone developed anything xe sent me an invite on discord but it became expired so idk if there is another channel I’m not aware of but I may start my own irc channel specificity for dev and setup an ftp.
Also I have 512 exact 2x256 and exact hdd 160seagate. Also is there and sdk for 1529? I was wondering if anyone knows if you can do debugging from boot or FireWire like we were thinking a few years back and update on that?
xe hit me up on discord, I’ve sent you some messages it’s Karcsi. looking for that old apple hdd image you had with the pdz info. do you still have it id like to try another attempt at recoverying pdz
hello, I think I have a xenon g5 image that is not released. I have something relate to giano and I found this on a wiki of the kit. (0431 - May 2004 - Kernel used in the Microsoft Giano framework) please id love to know what I have.